Smart Lifter
1. Controlled by servo system, the drive motor adopts imported servo motor.
2. Suspension mode: the whole suspension up and down stroke is not less than 2.5 meters. Intelligent lifting device in the suspended state, with the function of self-balancing, the operator does not need to control the device itself and the handle, only need to control the workpiece can be light to achieve the workpiece rise, fall. The system will detect the weight of the workpiece in real time no matter the weight increases or decreases to keep it in balance.
3. Speed: The maximum speed of rising and falling is ≤15m/min, and can be limited below the maximum speed; the actual running speed in floating mode is determined by the continuous longitudinal force applied to the induction handle, the greater the force, the faster the running speed and vice versa.
4. Control: equipped with induction handle, induction handle internal components sealed and equipped with pressure (photoelectric) sensors, can feel the force signal in the vertical direction in real time to control the direction of operation and speed of the system up and down. Operation of the induction handle detects the operator's vertical operating force (≤ 10N); the size of the required operating force can be changed by adjusting the sensitivity of the induction handle.
5. The system provides mechanical limits.
6. The workpiece can be operated directly by hand without touching the handle in hover mode. After the workpiece is finished releasing, no additional switching is needed, the system automatically switches back to the induction handle state to prevent the system from sudden upward movement.
7. Intelligent hoist has power failure protection, when a power failure failure occurs, the equipment will be stopped in place by the fail-safe device, when the power is supplied again, until an operator activates again the equipment can run immediately without any delay, and all the saved settings of the equipment will not be lost.
8. Intelligent hoist has overload protection function, when the equipment in the load exceeds its rated lifting capacity will automatically protect, can not lift. Overload protection will start automatically, the lifting speed control will fail, and only the descending control will be allowed to ensure the work safety.
9. Intelligent hoist has anti-bounce function no matter in handle mode or suspension mode, when the load changes suddenly, the device will not deflect and bounce, thus reducing the potential for injury accidents.
10. The intelligent hoisting device has upper and lower mechanical limit, which can stop unconditionally when running to the highest and lowest point to prevent the heavy load from rushing to the top.
11. Intelligent hoist can be manually mechanical limit, the limit protection point is precise and reliable.
12. Intelligent hoist provides handle sensitivity adjustment (10 level adjustment).
13. The overall industrial protection level of the equipment ≥ IP 54 (waterproof, dustproof), safety certification in line with the European standard ISO 4301/1.
14. LED panel, double button operation, simple and convenient.
15. Intelligent hoist can change the speed at will by changing the operating force of the handle without any presetting, and can also set the rising and falling speed at the same time, so it is not limited by any working conditions.
16. Intelligent hoisting device has the function of personnel in place, when the hand suddenly leaves the control handle, the hoisting device immediately stops rising or falling, and does not allow the situation of continuing to rise and fall.
17. The display of the handle must be able to show the weight of the lifted object for the operator's reference
18. The operating handle can be rotated 360° for the convenience of personnel.
19. Configured with a single-chip integrated circuit control module, the module is installed with a fault indicator, which can quickly determine the cause of the fault when the device is faulty and quickly eliminate the fault.


智能提升机


智能提升机


智能提升机


智能提升机


智能提升机


Previous page
1
2
3
Next page

Cantilever crane
The working intensity is light, composed of column, rotary arm, rotary drive device and chain electric hoist, the lower end of the column is fixed on the concrete foundation through the anchor bolt, driven by cycloid reducer cantilever rotary, electric hoist in the cantilever I steel for about straight line operation, and lifting heavy objects. The spiral arm is hollow steel structure, light weight, large span, large lifting weight, economic and durable. Built-in walking mechanism, using special engineering plastic walking wheel with rolling bearing, small friction force, walking light; Small size, especially to improve the hook stroke. (The system can also be configured with domestic or imported full pneumatic hoist) All specifications have a common advantage: light weight, long rotary arm, large lifting weight, installation, operation, maintenance is simple. They are fully self-contained and are ideal for job cranes and for outdoor yards and loading platforms. The fixed column covers a small area. Maximum lift height can be obtained with very small lift headroom

Vacuum suction crane
The equipment adopts vacuum pump negative pressure station as the vacuum generating device, automatic vacuum degree adjustable control, vacuum pump maintenance is convenient, the whole equipment is equipped with 6 vacuum suckers, multi-point adsorption to ensure that the steel plate in the process of handling can maintain a high level without tilt; The position of each sucker on the beam is adjustable, and the position of each beam on the main beam is also adjustable. At the same time, each sucker is equipped with a manual ball valve to control the opening and closing, so as to ensure that the same equipment is suitable for steel plates up to 3000mm

Fully automatic manipulator
The utility model relates to an automatic manipulator operated by simulating human hands. It can be fixed procedures to grab, carry objects or handle tools to complete some specific operations. The application of manipulator can replace people engaged in monotonous, repetitive or heavy manual labor, to achieve the mechanization and automation of production, to replace people in the harmful environment of manual operation, improve working conditions, to ensure personal safety, so widely used in mechanical manufacturing, metallurgy, electronics, light industry and atomic energy and other departments. Industrial production departments, used in high temperature, serious pollution in the place to take out work parts and loading and unloading materials. Automatic manipulator is usually used as an additional device for machine tools or other machines, such as loading and unloading and transferring the workpiece on automatic machine tools or automatic production lines, and changing the tool in the machining center, generally without independent control devices. The application of automatic manipulator in forging industry can further develop the production capacity of forging equipment and improve the working conditions such as heat and fatigue.
Search online
搜索
Quality wins customers, integrity creates the future
Contact us
Mr.zhou:13390895768
15306205950
E-MAIL:szhaijun02@163.com
ADD:China. 255 Songshan Road, High-tech Zone, Suzhou City
Suzhou Haijun Automation Machinery Co., Ltd. | Copyright 2021 All Rights Reserved. 苏ICP备13022660号-1 | power by:300.cn